 |
|
|
|
Standard
Post Mounted System
The system comprises of a heavy gauge aluminium pole to which the banner
is sleeved. The pole is secured into a steel electro-plated bracket with
a removable plated locking pin. Plastic collars retain the banner from
both sides (see our table below for safety limitations to size of banner).
The
standard post-mounted banner pole system is designed for use
on round lamp columns or similar vertical supports
(from 75mm-150mm diameter) fixed by means of stainless
steel banding or our new reusable Sign-torque* clip located
in the formed recess of the bracket.
Max Banner Width 915mm
The banner can be fitted on its own
or in pairs. The outside diameter (OD) of the banner pole
is 27mm (circumference
84mm). To comfortably accommodate the banner pole the
loop or pocket stitched into the banner should be no
less than 65mm in width.
To
suit banner width:
455mm £118, 610mm £120, 760mm £123, 915mm £126
Priced
per set of top and bottom poles - without fixings.
Prices
exclude banner, VAT
& delivery.
* Sign-torque clips from £7.50 each, see below.
|
|
|
|
Standard
Wall Mounted System
The system comprises of a heavy gauge aluminium pole to which the banner
is sleeved. The pole is secured into a steel electro-plated bracket with
a removable plated locking pin. Plastic collars retain the banner from
both sides (see our table below for safety limitations to size of banner).
The
wall mount bracket is 75mm wide and 130mm deep. It has 4
pre-drilled holes suitable for M8 fixings. We can supply
the M8 sleeve anchor bolts at 55mm or 70mm long.
To
suit banner width:
455mm £116, 610mm £119, 760mm £122, 915mm £125
Priced
per set of top and bottom poles - including fixings.
Prices exclude banner, VAT & delivery.
|
|
|
|
Self
Tensioning System
Here is a true self-tensioning banner system that is low cost, high value,
very effective and displays your graphics to their best effect whatever
the weather. The standard system is good but does not compensate for expansion
of PVC due to wind and heat. This leads to a ‘slap’ factor
that can destroy both the banner and the fittings. Our self-tensioning
system helps to alleviate these problems. Easy to install, easy to adjust.
Banners using this self-tensioning method have to be made in a special way. We will gladly quote you for a blank banner or to finish your preprinted banners to this specification when being fitted to this system.
Post
Mounted to suit banner width:
455mm £129, 610mm £132, 760mm £134, 915mm £137
Wall
Mounted to suit banner width:
455mm £127, 610mm £130, 760mm £133, 915mm £136.
Price
per set of top and bottom poles complete
with self-tensioning components. Wall fixings
extra
if required.
Prices exclude banner, VAT & delivery.
* Sign-torque clips from £7.50 each, see below.
|
|
Maximum
recommended banner sizes for all above systems |
| Banner
Width |
455mm |
610mm |
760mm |
915mm |
| Banner
Drop |
4.5m |
2.5m |
1.75m |
1.0m |
|
|
Wire
Supported System
Wall Mounted
Based on the very successful, competitively priced wall mounted
banner pole, we have engineered a conversion kit that will safely handle
banner
sizes up to 6 metres x 1 metre.
This is a wall mounted heavy duty support that takes
the strain out of fitting big banners. A system that helps
you to keep the initial tension on the banner. Full instructions
provided with kit.
Post Mounted
There is a natural tendency for banner poles
to droop. Keeping a banner properly tensioned adds to its
life
and
gives a
much better presentation to it’s image.
You can now also upgrade your existing post-mounted system by buying
the
additional
wire support kit.
It is important that a qualified engineer assesses the suitability
of the structure to withstand the additional wind loading
created by the installation of any of the assemblies on this
page.
Wall
Mounted Wire Support System:
For banners 1 metre by up to 6
metre drop
To
suit banner width 455-610mm £104
To suit banner width 760-915mm £106
Post
Mounted Support Kit:
For use with either
standard or self tensioning system.
To suit banner width 455-610mm £48
To suit banner width 760-915mm £50
Prices
per pair including 2 support wires.
Excludes
banner, VAT & delivery.
* Sign-torque clips from £7.50 each, see below.
|
|
|
|
Sign-Torque
Stainless Steel Grip Clip Banding System
Now there is an easier, quicker, safer way to fix banner poles to posts.
Sign-Torque
consists of a high tensile stainless steel band with
a special worm drive mechanism. Set in this is
a hardened, tamper resistant screw that only receives the
specially designed tools. Choose between the hand held ‘T’ bar
screwdriver that can alter its angle of drive for even
greater torque or a special drill bit for speed and efficiency – or
use both for even faster fitting.
We
now bring you a range of specially designed Sign-Torque bands to fit
from 55mm to 340mm diameter posts. No fuss, no bother, they are even
adjustable and re-usable. They will certainly make the job of fitting
post-mounted banner poles quicker and easier. You save time,
money and effort.
Sign-Torque
Grip Clips for post sizes:
| TTK70
- (55-70mm) |
£30 pack |
| TTK100
- (70-100mm) |
£34 pack |
| TTK130
- (100-130mm) |
£36 pack |
| TTK190
- (130-190mm) |
£39 pack |
| TTK250
- (190-250mm) |
£42 pack |
| TTK340
- (250-340mm) |
£48 pack |
Priced
per pack of 4, including drill bit.
Prices
exclude VAT & delivery.
|
|
|
|
|
|
